Thermostat cycle rate

Thermostat cycle rate

Every heating system type will deliver heat to the house at a slightly different rate. The CT provides you with the flexibility to set the cycle rate adjustment to match your specific heating system, whether it is gas or oil forced air, high efficiency forced air, electric forced air, or baseboard hot water.

Step 1: Remove the thermostat from the wallplate. Pull the lower right corner of the thermostat toward you until it detaches from the wallplate. Step 2: Following the directions on the back of the thermostat or in the table below, adjust the A and B screws to match your system type.

Step 3: Replace thermostat on the wallplate by lining up the top of the thermostat with the top of the wallplate, and then pushing the thermostat onto the wallplate until it snaps on. The CT uses two AA alkaline batteries. Where are the batteries located? The two AA alkaline batteries are located under the battery cover on the left side of the thermostat. The cover is easily removed by pulling from the bottom of the battery cover. There is also a small opening at the bottom of the battery cover if you need to use a coin to release the cover.

The optimum schedule would be to replace the batteries every fall before the heating season. The thermostat's display will read "bAt Lo" 1 to 2 months before the batteries run out completely. Replace the batteries as soon as possible after this indication appears in the display. As the batteries are running low, a "bAt Lo" indicator will flash for 1 to 2 months before batteries run out completely. Replace the batteries as soon as possible after the indicator starts flashing.

Cycle rate

After the batteries are completely dead, the "bAt Lo" indicator will disappear, leaving a completely blank display. The thermostat will not operate the heating or cooling system until new batteries are installed. First, replace the batteries with a new set of AA alkaline batteries. If you insert the new batteries within 20 to 30 seconds of removing the old ones, you will not have to reprogram the thermostat.

If the bAt Lo indication does not clear itself once new batteries are placed in the device install the batteries backward for 5 seconds, take them out, and reinstall correctly.

Eventually pm should come up and you can reprogram the thermostat. You may also want to clean the terminals with electrical contact cleaner and a soft cloth. Do not use a sharp object like a screwdriver or knife to clean terminals as this may cause permanent damage to the coating on the terminals.

If neither of these options clear the bAt Lo indicator, the thermostat should be replaced.It looks like you're new here. If you want to get involved, click one of these buttons! The Wall. Click here to Find a Contractor in your area. Here are the website rules, as well as some tips for using this forum. Need to contact us? I recently checked out a thread on the wall about thermostats. I saw a recommendation to change from the older style mercury bulb thermostat with anticipator to a newer digital style without an anticipator.

I have never been satisfied with the anticipator operation on my current Honeywell TD thermostat. It has a cycles per hour setting. I checked Honeywell website and I was unable to find any information on how this setting works other than how to set it.

Seems like a good value for the price they are asking for it. Anybody have any experience with this thermostat or some insight on the cycles per hour feature as it relates to hot water boilers? I am trying to compare this model with a Honeywell focus pro series which costs twice as much. Is it a case of: You get what you pay for or would I be purchasing more than I need?

John Ketterman Member Posts: May The Honeywell rule is 1 cycle for steam, 3 for hot water, 6 for forced air, 12 for electric.

You start witht hat and then change the number until you like the results. Honeywell has always been a little vague about this setting: just because you set 3 doesn't mean you'll actually get 3 cycles per hour. I suspect that when you change the number of cycles, you are not directly setting a specific number of cycles, but changing the difference between the "on" temperature and the "off" temperature.

I have no proof of this. Honeywell claims that the only point of an anticipator is to set the number of cycles per hour, but this is not quite correct. Cycles per hour All thermostats cycle boilers from 1 to many cycles per hour. The amount of boiler cycles that a boiler will go thru in an hour is a funtion of the jheat loss in your building. If you need to keep a uniform temperature in the house let the thermostat cycle the boiler by the need for heat input. If you want to save fuel you waste your money by buying a T stat that will cycle the boiler less frequently.

The less the boiler runs the less heat input you will get and that will lower the temperature in the house. You can accomplish the same thing buy lowering your thermostat to lower temprature.

I come from the school of kiss. I learned that bells and whistles do not accomplish the thing you want done. As for reset thermostats that can only be used on a hot water system or a two pipe vaccum steam system that can produce a vacuum up to 22 inches of mercury. If you have a simple steam system a set back thermostat can provide you as many cycles per hour you want.

The benifit of the set back thermostat is if the set backs do not do what you want you can remove the very cheap plastic pins and use the T Stat with out a set back.

What's scary is that maybe you install heating systems Welcome It looks like you're new here. Sign In Register. Categories Thermostats with adjustable cycle rates are something any home owner can install to lower power cost and help an HVAC system last longer. All thermostats have a set temperature that will turn on and off a heating and cooling system.

It is also sometimes referred to as the cycle rate since it is the cycle that a unit such as an air conditioner turns off and on. When HVAC units are turned on and off constantly it takes a toll on the equipment leading to parts wearing out and needing to be replaced. A unit that cycles often can also lead to larger electric bills. Why is there Higher Electricity Cost? When an air conditioner first turns on is when it has the biggest power consumption.

thermostat cycle rate

This is the reason that short cycles can run up a power bill. For example, an air conditioner must pump refrigerant through a cooling system which takes more work at the start then it does after it has been running.

Your current thermostat may be capable of changing the cycle rate which can be seen in its manual. Adjustable Cycle Rate Differential Thermostats. It can be set from 1 degree too as much as 3 degrees in half-degree steps. It also has a 5-minute minimum compressor off-time which is great when power is interrupted as too not damage the compressor. The temp inside is set to 75 degrees in the summer. This unit runs for 45 minutes, turns off for 5 minutes the back on again.

We are being told by the installer that this is normal running time for these new energy efficient units. Is this normal? We have a 3 ton unit for a sq ft house.

A 3 ton unit is not enough for a home your size. A5 ton unit would be pushing the limit unless your home was supper efficient. So, how do we remove or turn-off the 1 degree differential to keep the temp at what i set, not something different from what i set?

The thermostat that the installer provided is a honeywell T6pro programmable thermostat. The problem is that the furnace cycles on for 5 minutes and off for 15 minutes day and nite. The installer turned off the program which supposedly senses the room temperature change before it actually goes down.

He says this cannot be changed. Any suggestions as to what would be a sutable replacement to use.A heat anticipator is an electrical resistor device mounted in the center of many older mechanical thermostats, including the familiar Honeywell dial-type thermostat.

Ideally, it turns the furnace's burners off a short time before the room reaches the desired temperature. This is to compensate for the fact that furnaces continue to produce and distribute heat for a short while until the heat exchanger cools down. If the shut-off is properly timed, the room temperature edges up to reach the precise desired temperature a short while after the burners shut off. The heat anticipator essentially consists of a small disc attached to the bimetallic coil of the thermostat.

The disc has a thin wire on its surface and an adjustment arm that touches the wire. The position of the arm determines the electrical resistance of the wire, which in turn affects how hot the wire gets.

As the wire heats up, it warms the bimetallic coil, which in turn shuts down the gas burners early, according to the heat anticipator's setting. When the heat anticipator in your thermostat is out of adjustment, it can cause the furnace to "short cycle" turn on and off frequently or to exceed or never reach the desired thermostat heat setting. Fortunately, this problem is often easy to correct by adjusting the heat anticipator.

Remove the thermostat cover. Using a torpedo level, make sure the thermostat body is level on the wall. If not, the thermostat's mercury switch will not work properly. Adjustments can be made fairly easily by loosening the mounting screws, rotating the thermostat body to the desired position, then retightening the mounting screws.

It will also have a lever arm and indicator relating to the calibration marks.

Heat pump thermostat wire color code

This is the heat anticipator adjustment lever arm. If the furnace is exceeding or never reaching the desired set temperature, then move the adjustment lever away from the "LONGER" setting by one calibration mark. Once the appropriate adjustment is made, let the furnace run and the temperature stabilize for a period of two to three hours. If necessary, repeat the above procedure until the thermostat works properly.

If the problem persists and you cannot resolve the problem with these steps, you may need to replace the thermostat. If you have trouble getting your mechanical thermostat to properly time the shut-off, you may want to consider installing a new electronic thermostat. Electronic thermostats are so precise that there is no need for a heat anticipator.

Best of all, most electronic thermostats have programmable controls that allow you to preset room temperatures for convenient, energy-saving operation. Examine the Thermostat Remove the thermostat cover. Tip If you have trouble getting your mechanical thermostat to properly time the shut-off, you may want to consider installing a new electronic thermostat. Show Full Article.The creation of a custom schedule will satisfy comfort needs while optimizing energy savings.

Smart Response Learning eliminates the guessing work out of programming by allowing the Wi-Fi Smart Color Thermostat to learn preferred heating and cooling cycle times. This feature ensures the correct temperature right when it's required. The inclusion of a customizable color touchscreen display will invite owners to create their own unique look when matching their home's surrounding decor.

The Honeywell Total Connect Comfort App provides immediate and convenient access via smartphone, tablet or computer. This level of access and customization ensures the ultimate in peace of mind as owners will have complete control regardless of setting. Intelligent Alerts add even more layers of versatility by informing homeowners when air filters and humidifier pads require changing.

Optional password protection allows only designated users to access the security settings and locking options. Just great, easy to install and setup. Up and running in 5 minutes and 10 more to do schedules. Just great product and features. This thermometer provides all the features I want for my master bedroom. I am very pleased with my purchase from Honeywell.

Home Owner. If could give higher rating the 5 would. Easy to wire, program and connect to Alexa. I tried to follow the instructions, and could not sync them with my iPhone because I could not figure out the specific model of thermostat in the instructions.

Other than that I like the product. You can adjust brightness in preferences. Sergio T.

My system cycles too fast (or slow). What should I do?

You can adjust the colors in Settings and in Preferences you can set the brightness. I have mine set to a black screen.Temperature swing, is the difference between the turn-on and turn-off temps on a thermostat, whether heating or cooling.

The swing setting, when the t-stat has it, often ranges between one and three degrees. Many modern t-stats have this setting. This allows accounting for differing home build types and locations, types of furnaces, and personal comfort choices.

So without taking the t-stat apart, you cannot adjust this via the menus. Instead, they hard coded the temperature swing setting. So this t-stat tries to keep the room temp within 0. The AC comes on when the room temp rises 0. Or, the heating comes on when the temp drops 0.

Setting Honeywell Thermostat Swing on RTH8580WF

It uses its Smart Response tech when enabled. And indeed, we found this good enough in our apartment HVAC system. We never felt too hot or too cold there with this t-stat at the helm. Now you could try adjusting the heating cycle rate setting parameter But they give no similar setting for cooling. The choices are: 5-Gas or oil furnace; 9-electric furnace; 3-hot water or high efficiency furnace; 1-steam or gravity furnace powered by gas or oil.

Then, let the system run for several hours. Note any too-much temperature swings. This is the price of more exact comfort control. But the room may get too cold before the furnace kicks on. Or it might get too hot before it kicks off. In either case, try adjusting the set temp up or down respectively by a degree or two. This may help. Yet if the temperature swing is still too great, THEN try changing the heating cycle rate. This controls how many times per hour this t-tat turns on your furnace.

Note that longer cycle times allow larger temperature swings. Also, shorter cycle rates allow for smaller swings and tighter temp control. Skip to content. Like this: Like LoadingInspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website. These little slide or toggle switches may control the heating system on-off cycle rate or burner-on time in a manner similar to the heat anticipator feature found in other room thermostats.

Here we describe various types of internal or "hidden" switches found in some wall thermostats and in a table form we summarize their proper setting. In most cases you can safely install a new room thermostat without worrying about these switches - just leave the switch or switches in the factory-set position. But in some circumstances setting the switches correctly may involve a change.

Gas or oil this is the factory switch setting for systems that control the fan in a call for heat. This setting is for systems that allow the thermostat to control the fan in a call for heat, if a fan wire is connected to the G terminal. Fred asked:. Fred, There is no traditional heat-anticipator adjustment as was found on some older thermostats we describe in this article series.

thermostat cycle rate

We should simply follow Honeywell's recommendations for the CT 87K thermostat. In the CT87 owner's manual given below you'll see that the CT87N is for 24 Vac heating and cooling systems while the CT87K is for 24 Vac heating systems - that is the N model controls both heating and air conditioning. If the batteries fail the thermostat may fail to provide heating or cooling and the building may suffer accordingly.

This switch is located at the top right side of the thermostat beneath the removable top cover. This is a manual override switch. If you set this switch to ON or EMER left this will disable the heat pump and will mean that you are relying on your auxiliary heat or backup heat system only.

thermostat cycle rate

This makes sense if your heat pump is in trouble or inadequate and you want to force backup-heat to be used instead. Watch out : as purchased, in our thermostat we found this switch had been set to ON to the left as you can see in our photo.

If your thermostat is not working properly, and provided you've already checked the obvious faults such as no power, bad batteries, loose wiring, improper settings, or manual switches in the wrong position, then you might try pressing this button.

An alternative and more involved hard reset of the thermostat could also be performed by removing its batteries and disconnecting its thermostat wiring. Swing Rate: the desired variance in temperature between the 3M setting and the room temperature before the heating or cooling system will turn on.

The swing rate can be varied from 0. Then press the Home button leftmost button, bottom row to store the setting. Watch out : unless you have bright light and good eyes the names, labels, and functions of the forest of setting buttons on this thermostat are quite difficult to read.


Comments

Leave a Reply

Your email address will not be published. Required fields are marked *